月柿提取物体外抗氧化活性研究

目的以月柿提取物为原料,研究其对2,2-联苯基-1-苦基肼基(1,1-diphenyl-2-picrylhydrazyl,DPPH)自由基的清除能力,并测定其多酚类物质没食子酸的含量。方法检测波长为518 nm,反应时间为40 min条件下,以IC_(50)值(清除率为50%时,抗氧化剂的浓度值)作为抗氧化能力评价指标,并采用高效液相色谱法测定其没食子酸含量。结果月柿提取物对于DPPH自由基有良好的清除作用,其IC50值为0.1868 mg/mL,与常用抗氧化剂作用相当,且月柿提取物中没食子酸含量为1.65 g/kg。结论月柿提取物具有很强抗氧化活性,作为化妆品及功能性食品原料有广阔的开发前景。     

煤粉锅炉脱硫系统中除尘器压差过高原因及解决方案

高倍率灰钙循环烟气脱硫技术在神东矿区的煤粉锅炉环保改造项目中已投入建设并成功运行,脱硫率可达95%以上。在NGD系统的运行调试期,布袋除尘器压差的数值及其上升速度均较改造前有大幅提高,影响了锅炉系统的正常运行并降低了布袋除尘器的运行效率。为了解决此问题,先分析滤料透气性降低而导致布袋除尘器压差上升的根本原因,再结合现场调研情况对NGD系统工况下的烟气含湿量、烟气温度、烟气灰浓度、除尘器本体的问题以及上游锅炉系统问题逐一进行对比和分析,并找出问题产生的各主要因素。NGD系统中布袋除尘器差压升高的原因包括多方面,为了使NGD系统的运行更加稳定,需要使除尘器适应NGD系统的工况并对系统中部分设备进行改造。在未来NGD系统的设计中,布袋除尘器需按高浓度烟气设计,且针对煤粉工业锅炉的运行、维护特性应加入对烟气中含水量的监测及对布袋除尘器的相应保护措施。     

Ultrasonic-vibration-assisted laser annealing of fluorine-doped tin oxide thin films for improving optical and electrical properties: Overlapping rate optimization

An ultrasonic-vibration-assisted laser annealing method was developed to enhance the performance of fluorine-doped tin oxide (FTO) thin films. The influences of ultrasonic vibration, laser scan line overlapping rate (L_OR) and laser spot overlapping rate (S_OR) on surface morphology, FTO layer thickness, RMS roughness, crystal structure and photoelectric properties of the FTO films were investigated. The results indicated that the presence of ultrasonic vibration during laser annealing could significantly enhance the film compactness, and using moderate L_OR and S_OR values resulted in significantly decreased FTO layer thicknesses and RMS roughnesses as well as slightly increased crystallite sizes, thus yielding significantly improved optical transmittance values and slightly enhanced electrical conductivity values. It was found that the optimal L_OR and S_OR values for ultrasonic-vibration-assisted laser annealing of the FTO films were 80% and 90%, respectively. The as-obtained film possessed the best overall photoelectric property with an average transmittance (400–800?nm) of 85.9%, a sheet resistance of 8.7?Ω/sq and a figure of merit of 2.51?×?10^–2 Ω^–1. This work may be of great significance in terms of performance optimization of transparent conducting oxide (TCO) thin films.     

Large increase of Curie temperature in (110)-oriented La0.7Sr0.3MnO3 films

From the perspectives of scientific researches and practical applications, it is desirable to explore high operating temperature ferromagnetic films. The effect of biaxial strain on magnetic properties of (110)-oriented La_0.7Sr_0.3MnO₃ films was studied. High quality La_0.7Sr_0.3MnO₃ films were grown on (110)-oriented perovskite single crystal substrates using pulsed laser deposition, varying substrate-induced misfit strains from ??2.27–0.75%. A remarkable enhancement of Curie temperature has been achieved for (110)-oriented La_0.7Sr_0.3MnO₃ films clamped with small misfit strains (i.e., grown on LAST (110)). The enhanced Curie temperature of (110)-oriented La_0.7Sr_0.3MnO₃ films could be attributed to the misfit strain between the films and the underlying substrates and may have technological implication for applications at high temperature environments.     

Tribological behaviour of a 3Y-TZP/Ta ceramic-metal biocomposite against ultrahigh molecular weight polyethylene (UHMWPE)

This study aims to evaluate the tribological behaviour of 3Y-TZP/Ta (20 vol%) ceramic-metal composites and 3Y-TZP monolithic ceramic prepared by spark plasma sintering (SPS) against ultrahigh molecular weight polyethylene (UHMWPE). According to the results of pin (UHMWPE)-on-flat wear test under dry conditions, the UHMWPE – 3Y-TZP/Ta system exhibited lower volume loss and friction coefficient than the UHMWPE – monolithic ceramic combination due to the presence of an autolubricating layer that provides sufficient lubrication for reducing the friction. Owing to the lubrication of the liquid media, under wet conditions obtained using simulated body fluid (SBF), similar behaviour is observed in both cases. Additionally, the ceramic and biocomposite materials were subjected to a low temperature degradation (LTD) process (often referred to as “ageing”) to evaluate the changes in the tribological behaviour after this treatment. In this particular case, the wear properties of the UHMWPE-biocomposite system were found to be less influenced by ageing in contrast to the case of the UHMWPE-zirconia monolithic material. In addition to their exceptional mechanical performance, 3Y-TZP/Ta composites also showed high resistance to low temperature degradation and good tribological properties, making them promising candidates for biomedical applications, especially for orthopaedic implants.     

Research on the identification performance of UHF RFID system considering the correlation of cascaded channel

The identification rate of UHF RFID system was restricted by multipath propagation effects.The system identification performance was studied considering the correlation coefficient between forward and reverse channels.Based on the generalized Rician fading channel model,the analytical expression of identification rate was derived under independent,full correlation and correlation cases.Compared with the existing analysis,the proposed uniform calculation formula of identification rate was for any correlation coefficient and kinds of channel conditions.The numerical computation and Monte-carlo simulations show that the influences of different correlation coefficients,channel conditions,sensitivity and distance on the identification rate.     

Numerical modeling assessment of mechanical effect in bovine leather drying process

Leather manufacturing involves a crucial energy-intensive drying stage in the finishing process to remove its residual moisture and generates important heat gradients. The numerical model presented in this study has been developed to describe the drying process of porous medium: bovine leather that undergoes deformation due to shrinkage. The mathematical formulation of fundamental heat, mass and momentum transfers’ phenomena during drying summarizes a two-dimensional model considering elastic behavior of bovine leather. The evolution of moisture content, temperature, and mechanical stresses during drying was discussed. The model was validated with experimental results. Numerical simulations show good agreement with experimental results. The study shows that the elastic model keeps the stress sign at the final stage of drying. The deformations induce tensional stresses near the surface equilibrated by compressive stresses within the product. They reached their maximum for normal stresses equal to 5.97 and 3.52?MPa at around 2145 and 868?s, respectively, for normal stresses along x and y directions and then decrease.     

Group sequential crossover trial designs with strong control of the familywise error rate

Crossover designs are an extremely useful tool to investigators, and group sequential methods have proven highly proficient at improving the efficiency of parallel group trials. Yet, group sequential methods and crossover designs have rarely been paired together. One possible explanation for this could be the absence of a formal proof of how to strongly control the familywise error rate in the case when multiple comparisons will be made. Here, we provide this proof, valid for any number of initial experimental treatments and any number of stages, when results are analyzed using a linear mixed model. We then establish formulae for the expected sample size and expected number of observations of such a trial, given any choice of stopping boundaries. Finally, utilizing the four-treatment, four-period TOMADO trial as an example, we demonstrate that group sequential methods in this setting could have reduced the trials expected number of observations under the global null hypothesis by over 33%.     

Validation of Models Predicting Nucleation Rates from Induction Times and Metastable Zone Widths

Three approaches for estimation of nucleation rates from induction time and metastable zone width (MSZW) were validated based on directly measured nucleation rates for paracetamol in ethanol. To quantitatively predict nucleation kinetics using Kubota's methods it is necessary to know the minimum detectable number concentration of nuclei. This was found by determination of light transmission of a series of diluted suspensions of newly nucleated crystals where the size had already been assessed by optical reflection measurement (ORM). The measured nucleation rates strongly depended on both temperature and supersaturation. The Nyvlt method predicted nucleation rates in this system reasonably well; however, it gave slightly low estimates for all temperatures. The methods of Kubota provided nucleation rates that were low by an order of magnitude.